Hyundai Elantra (CN7): Body (Interior and Exterior) / Fuel Filler Door

Hyundai Elantra (CN7) 2021-2026 Service Manual / Body (Interior and Exterior) / Fuel Filler Door

Components and components location

Component Location

1. Fuel filler door


Repair procedures

Replacement
[Fuel filler door]
   
•
When removing with a flat - tip screwdriver or remover, wrap protective tape around the tools to prevent damage to components.
•
Put on gloves to prevent hand injuries.
1.
Open the fuel filler door (A).

2.
Loosen the mounting bolts and remove the fuel filler door (A).
Tightening torque :
3.9 - 5.9 N.m (0.4 - 0.6 kgf.m, 2.9 - 4.3 lb-ft)

3.
To install, reverse the removal procedure.
   
•
Make sure the fuel filler door locks / unlocks and opens / closes properly.
[Fuel filler door cable]
   
•
When removing with a flat - tip screwdriver or remover, wrap protective tape around the tools to prevent damage to components.
•
Take care not to scratch the body surface.
1.
Remove the front seat assembly.
(Refer to Front Seat - "Front Seat Assembly")
2.
Remove the rear seat assembly.
(Refer to rear Seat - "Rear Seat Assembly")
3.
Remove the floor console assembly.
(Refer to Floor Console - "Floor Console Assembly")
4.
Remove the center pillar lower trim.
(Refer to Interior Trim - "Center Pillar Trim")
5.
Remove the cowl side trim.
(Refer to Interior Trim - "Cowl Side Trim")
6.
Remove the luggage side trim.
(Refer to Interior Trim - "Cowl Side Trim")
7.
Remove the floor carpet.
(Refer to "Floor carpet")
8.
Loosen the mounting bolt and remove the fuel filler door catch (A).
Tightening torque :
7.8 - 11.8 N.m (0.8 - 1.2 kgf.m, 5.8 - 8.7 lb-ft)
9.
Disconnect the fuel filler door barcket (A), remove the cable (B).

10.
To install, reverse the removal procedure.
   
•
Make sure the fuel filler door locks / unlocks and opens / closes properly.
[Fuel filler door catch]
1.
Remove the front seat assembly [LH].
(Refer to Front Seat - "Front Seat Assembly")
2.
Remove the front door scuff trim [LH].
(Refer to Interior Trim - "Front Door Scuff Trim")
3.
Remove the cowl side trim [LH].
(Refer to Interior Trim - "Cowl Side Trim")
4.
Remove the floor console assembly.
(Refer to Floor Console - "Floor Console Assembly")
5.
Separate the floor carpet to obtain space for removing the rear heating duct.
6.
Loosen the fuel filler door catch mounting bolt (A).
Tightening torque :
7.8 - 11.8 N.m (0.8 - 1.2 kgf.m, 5.8 - 8.7 lb-ft)

7.
Detach the cable (A) and remove the fuel filler door catch (B).

8.
To install, reverse the removal procedure.
   
•
Make sure the fuel filler door locks / unlocks and opens / closes properly.

    Repair procedures Replacement    â€¢ Do not apply sealant to the body. 1.Remove the trunk lid weatherstrip (A).

    Other information:

    Hyundai Elantra (CN7) 2021-2026 Service Manual: Repair procedures

    Diagnosis with Diagnostic tool1.In the body electrical system, failure can be quickly diagnosed by using the vehicle diagnostic system (Diagnostic tool).The diagnostic system (Diagnostic tool) provides the following information.(1)Fault Code Searching : Checking failure and code number (DTC)(2)Data Analysis : Checking the system input/output data s

    Hyundai Elantra (CN7) 2021-2026 Service Manual: Description and operation

    DescriptionRear Corner Radar is a system that measures the relative speed and distance from the following vehicles by using two electromagnetic wave radar sensors attached to the rear bumper, and detects any vehicle within the blind spot zone and gives off alarm.

    Categories

     
    Copyright © 2026 www.helantra7.com - 0.0187