Hyundai Elantra (CN7): Driveshaft and axle / Specifications

Hyundai Elantra (CN7) 2021-2025 Service Manual / Driveshaft and axle / Specifications

Specification
Engine
Transmission
Joint type
Max. permissible angle
Outer side
Inner side
Outer side
Inner side
GAMMA I 1.6 MPI
AT
BJ#22
CTJ#22
46.5°
23°
MT
BJ#23
CTJ#23
GAMMA II 1.6 MPI
CVT
BJ#22
CTJ#22
MT
BJ#23
CTJ#23
NU 2.0 MPI
AT
BJ#22
CTJ#22
MT
BJ#23
CTJ#23

Tightening torque
Item
N.m
kgf.m
lb-ft
Front
Tire wheel hub nut
107.9 - 127.5
11.0 - 13.0
79.6 - 94.0
Driveshaft caulking nut
274.6 - 294.2
28.0 - 30.0
202.5 - 217.0
Strut assembly lower mounting nut
156.9 - 176.5
16.0 - 18.0
115.7 - 130.2
Brake caliper mounting bolt
78.5 - 98.1
8.0 - 10.0
57.9 - 72.3
Wheel speed sensor mounting bolt
7.8 - 11.8
0.8 - 1.2
5.8 - 8.7
Brake disc mounting screw
4.9 - 5.9
0.5 - 0.6
3.6 - 4.3
Lower arm ball joint mounting bolt
68.6 - 80.4
7.0 - 8.2
50.6 - 59.3
Tie rod end ball joint mounting nut
34.3 - 44.1
3.5 - 4.5
25.3 - 32.5
Dust cover mounting bolt
3.9 - 5.9
0.4 - 0.6
2.9 - 4.3
Hub bearing mounting bolt
78.5 - 98.1
8.0 - 10.0
57.9 - 72.3
Rear
Tire wheel hub nut
107.9 - 127.5
11.0 - 13.0
79.6 - 94.0
Brake disc mounting screw
4.9 - 5.8
0.5 - 0.6
3.6 - 4.3
Brake caliper mounting bolt
78.5 - 98.1
8.0 - 10.0
57.9 - 72.3
Hub assembly mounting bolt
49.0 - 58.8
5.0 - 6.0
36.2 - 43.4

Lubricants
Engine
Transmission
Joint type
Lubricants
Quantity
GAMMA I 1.6 LPI
AT
BJ#22
RBA
90g +10g
CTJ#22
CW-13TJ
120g + 10g
MT
BJ#23
RBA
90g +10g
CTJ#23
CW-13TJ
125g + 10g
GAMMA II 1.6 MPI
CVT
BJ#22
RBA
90g +10g
CTJ#22
CW-13TJ
120g + 10g
MT
BJ#23
RBA
90g +10g
CTJ#23
CW-13TJ
125g + 10g
NU 2.0 MPI
AT
BJ#22
RBA
90g +10g
CTJ#22
CW-13TJ
120g + 10g
MT
BJ#23
RBA
90g +10g
CTJ#23
CW-13TJ
125g + 10g

    Troubleshooting Symptom Expected cause Countermeasure Leaning phenomenon of vehicleDefect on front suspension and steering.

    Special Service Tools Tool (Number and Name) Illustration Use 09495-3K000Band installerInstallation of ear type boot band09495-39100Band installerInstallation of hook type boot band09568-1S100Ball joint pullerRemove the ball joint front axle 09495-33000PullerRemove the spider assembly from the drive shaft

    Other information:

    Hyundai Elantra (CN7) 2021-2025 Service Manual: Receiver-Drier

    Repair procedures Replacement1.Remove the condenser.2.Remove the cap (A) on the bottom of the condenser with a L wrench. Tightening torque : 9.81 - 14.71 N.m (1.0 - 1.5 kgf.m, 7.2 - 10.8 lb-ft) 3.Remove the receiver-drier (A) from condenser using a long nose plier.

    Hyundai Elantra (CN7) 2021-2025 Service Manual: Blower Resistor (Manual)

    Repair procedures Inspection1.Measure the resistance between the terminals.2.The measured resistance is not within specification, the blower resistor must be replaced. (After removing the resistor)Replacement1.Disconnect the negative (-) battery terminal.

    Categories

     
    Copyright © 2025 www.helantra7.com - 0.0125