Hyundai Elantra (CN7): Body (Interior and Exterior) / Front Seat Belt

Hyundai Elantra (CN7) 2021-2026 Service Manual / Body (Interior and Exterior) / Front Seat Belt

Components and components location

Components

1. Front seat belt retractor
2. Height adjust
3. Front seat belt upper anchor
4. Rear seat belt retractor [RH]
5. Rear seat belt retractor [CTR]
6. Seat belt buckle [RH]
7. Seat belt buckle [LH, CTR]
8. Rear Seat belt lower anchor

Front Seat Belt Pretensioner

Components and components location

Components Location

1. Front seat belt pretensioner


Repair procedures

Replacement
   
•
When installing the belt, make sure not to damage the pretensioner.
1.
Remove the center pillar upper trim.
(Refer to Interior Trim - "Center Pillar Trim")
2.
Remove the center pillar lower trim.
(Refer to Interior Trim - "Center Pillar Trim")
3.
After loosening the front belt upper anchor mounting bolt, remove the front belt upper anchor (A).
Tightening torque :
39.2 - 53.9 N.m (4.0 - 5.5 kgf.m, 28.8 - 39.8 lb-ft)

4.
Separate the seat belt retractor connector (A) and pre-active seat belt connector (B).

5.
Loosen the mounting bolt (B) and (C), remove the front seat belt retractor (A).
Tightening torque :
Bolt B : 7.8 - 11.8 N.m (0.8 - 1.2 kgf.m, 5.8 - 8.7 lb-ft)
Bolt C : 39.2 - 53.9 N.m (4.0 - 5.5 kgf.m, 28.9 - 39.8 lb-ft)

6.
Install in the reverse order of removal.
   
•
After installing the front seat belt retractor, check that the air bag warning indicator illuminates for about 6 seconds when the ignition is ON and then goes out.
•
Make sure the connector is plugged in properly.
•
Replace any damaged clips (or pin - type retainers).

Height Adjust

Components and components location

Component Location

1. Height adjust


Repair procedures

Replacement
1.
Remove the front seat belt upper anchor.
(Refer to Front Seat Belt - "Front Seat Belt Pretensioner")
2.
After loosening the mounting bolts, remove the height adjust (A).
Tightening torque :
39.2 - 53.9 N.m (4.0 - 5.5 kgf.m, 28.9 - 39.8 lb-ft)

3.
To install, reverse the removal procedure.
   
•
Replace any damaged clips (or pin - type retainers).

Front Seat Belt Buckle

Components and components location

Components Location

1. Front seat belt buckle


Repair procedures

Replacement
1.
Remove the front seat assembly.
(Refer to Front Seat - "Front Seat Assembly")
2.
Disconnect the front seat belt buckle connector wiring (A).

3.
After loosening the mounting bolt, remove the front seat belt buckle (A).
Tightening torque :
39.2 - 53.9 N.m (4.0 - 5.5 kgf.m, 28.9 - 39.8 lb-ft)

4.
To install, reverse the removal procedure.
   
•
Make sure the connector Is connected in properly.
•
Replace any damaged clips.

    Components and components location Components1.Rear seat folding lever Repair procedures Replacement1.Fold the rear seat back assembly (A) by pulling the folding lever in the direction of the arrow.

    Components and components location Components1. Front seat belt retractor2. Height adjust 3. Front seat belt upper anchor4. Rear seat belt retractor [RH]5.

    Other information:

    Hyundai Elantra (CN7) 2021-2026 Service Manual: Photo Sensor

    Description and operation Description 1.The photo sensor is located at the center of the defrost nozzles.2.The photo sensor contains a photovoltaic (sensitive to sunlight) diode. The solar radiation received by its light receiving portion, generates an electromotive force in proportion to the amount of radiation received which is transferred to

    Hyundai Elantra (CN7) 2021-2026 Service Manual: Repair procedures

    Inspection1.Check for resistance between terminals in each switch position (LH).[LH : Audio + Hands free] Switch Resistance (±5%) SEEK Up430 ΩSEEK Down1.11 kΩMODE2.11 kΩMUTE3.11 kΩVolume (+)4.

    Categories

     
    Copyright © 2026 www.helantra7.com - 0.0135