| Specifications |
|
Item
|
Specification
| |
| Transmission model | D7UF1-2 (7DCT) | |
| Engine model | Gamma II 1.6 T-GDI (Gasoline) | |
| Clutch Type | Dry dual plate | |
| Gear ratio | 1st | 3.929 |
| 2nd | 2.318 | |
| 3rd | 1.957 | |
| 4th | 1.023 | |
| 5th | 0.778 | |
| 6th | 0.837 | |
| 7th | 0.681 | |
| Reverse | 5.304 | |
| Final gear ratio | 1st, 2nd, 4th, 5th | 4.857 |
| 3rd, 6th, 7th, R | 3.579 | |
|
Item
|
Specification
|
| Rated voltage | 12V |
| Initialize the rod length | 79.0 - 80.0 mm (3.1102 - 3.1496 in.) |
| Wear adjustment amount | 0.25 mm (0.0098 in.) @ 1 Click |
|
Item
|
Specification
|
| Power supply | 12V |
| Output type | CAN signals |
|
Item
|
Specification
|
| Power supply | 12V |
| Output type | Combination of output signals |
|
Item
|
Specification
|
| Type | Hall effect sensor |
| Output signal | High: 11.8 - 16.8 mA |
| Low: 5.9 - 8.4 mA |
| Tightening Torques |
|
Item
|
N.m
|
kgf.m
|
lb-ft
|
| Clutch engagement bearing | 9.8 - 11.8 | 1.0 - 1.2 | 7.2 - 8.7 |
| TCM mounting bolt | 7.8 - 9.8 | 0.8 - 1.0 | 5.8 - 7.2 |
| Clutch actuator & TCM assembly mounting bolt | 19.6 - 26.5 | 2.0 - 2.7 | 14.5 - 19.5 |
| Fork cover mounting bolt | 3.9 - 5.9 | 0.4 - 0.6 | 2.9 - 4.3 |
| Gear actuator mounting bolt | 19.6 - 26.5 | 2.0 - 2.7 | 14.5 - 19.5 |
| Input shaft speed sensor mounting bolt | 9.8 - 11.8 | 1.0 - 1.2 | 7.2 - 8.7 |
| Inhibitor swtich mounting bolt | 9.8 - 11.8 | 1.0 - 1.2 | 7.2 - 8.7 |
| Manual lever mounting nut | 17.4 - 24.5 | 1.8 - 2.5 | 13.0 - 18.1 |
| Oil drain plug | 44.1 - 58.8 | 4.5 - 6.0 | 32.5 - 43.4 |
| Oil filler plug | 58.8 - 78.5 | 6.0 - 8.0 | 43.4 - 57.9 |
| Shift cable bracket mounting bolt | 19.6 - 26.5 | 2.0 - 2.7 | 14.5 - 19.5 |
| Shift cable mounting nut | 9.8 - 13.7 | 1.0 - 1.4 | 7.2 - 10.1 |
| Shift cable retainer mounting nut | 11.8 - 14.7 | 1.2 - 1.5 | 8.7 - 10.8 |
| Shift lever assembly mounting bolt | 8.8 - 13.7 | 0.9 - 1.4 | 6.5 - 10.1 |
| Stater motor mounting bolt | 49.0 - 63.7 | 5.0 - 6.5 | 36.2 - 47.0 |
| Transmission support bracket mounting bolt | 88.3 - 107.9 | 9.0 - 11.0 | 65.1 - 79.6 |
| Transmission bracket mounting bolt | 58.9 - 78.5 | 6.0 - 8.0 | 43.4 - 57.8 |
| Transmission upper mounting bolt (Transmission=>Engine) | 42.2 - 53.9 | 4.3 - 5.5 | 31.1 - 39.8 |
| Transmission lower mounting bolt (Engine=>Transmission) | 42.2 - 48.1 | 4.3 - 4.9 | 31.1 - 35.4 |
| 42.2 - 53.9 | 4.3 - 5.5 | 31.1 - 39.8 |
| Lubricants |
|
Item
|
Capacity
|
Recommended
|
| Transmission oil | 1.6 - 1.7 â„“ (0.42 - 0.45 U.S.gal., 1.69 - 1.80 U.S. qt., 1.41 - 1.50 lmp qt) | SAE 70W, API GL-4 Recommended transmission oil : H.K.SHELL: SPIRAX S6 GHDE 70W DCTF PLUS, SK: HK D DCTF TGO-10 PLUS |
| Input shaft 1/2 spline | 0.15 - 0.25 g | Extreme pressure grease for vehicle |
| Clutch engagement fork | 0.1 - 0.2 g | Extreme pressure grease for vehicle |
Special Service Tools Tool (Number and Name) Illustration Use 09200-3N000Engine support fixture(Beam)Removal and installation of the transmission.
Repair procedures Oil Specification1.The HFC-134a system requires synthetic (PAG) compressor oil whereas the R-12 system requires mineral compressor oil. The two oils must never be mixed.2.Compressor (PAG) oil varies according to compressor model. Be sure to use oil specified for the model of compressor.
Components and components location Components[This illustration shows the LHD type. RHD type is symmetrical.][Connector A] Pin No Function Pin No Function 1Low (Register specifications)4Middle Low (Register specifications)2Common (Register