Hyundai Elantra (CN7): Driveshaft and axle / Rear Axle Assembly. Rear Hub - Carrier

Hyundai Elantra (CN7) 2021-2026 Service Manual / Driveshaft and axle / Rear Axle Assembly. Rear Hub - Carrier

Components and components location

Components
[Rear disc brake type]

1. Rear brake disc
2. Hub bearing assembly
3. Dust cover
4. Rear carrier

[Rear drum brake type]

1. Rear drum
2. Rear hub assembly
3. Brake assembly
4. Spacer

Repair procedures

Removal
[Rear disc brake type]
1.
Loosen the wheel nuts slightly.
Raise the vehicle, and make sure it is securely supported.
2.
Remove the rear wheel and tire (A) from the rear hub.
Tightening torque :
107.9 - 127.5 N.m (11.0 - 13.0 kgf.m, 79.6 - 94.0 lb-ft)
   
•
Be careful not to damage the hub bolts when removing the rear wheel and tire (A).

3.
Remove the rear brake caliper.
(Refer to Brake System - "Rear Disc Brake")
4.
Loosen the screw and the remove the rear break disc (A).
Tightening torque :
4.9 - 5.9 N.m (0.5 - 0.6 kgf.m, 3.6 - 4.3 lb-ft)

5.
Disconnect the rear wheel speed sensor connector (A).

6.
Remove the hurb bearing assembly after loosening the hurb bearing mounting bolts (A).
Tightening torque :
49.0 - 58.8 N.m (5.0 - 6.0 kgf.m, 36.2 - 43.4 lb-ft)

7.
Separate the backing plate and extra bracket after loosening the mounting bolts.
Tightening torque :
2.0 - 2.9 N.m (0.2 - 0.3 kgf.m, 1.4 - 2.2 lb-ft)

[Rear drum brake type]
1.
Loosen the wheel nuts slightly.
Raise the vehicle, and make sure it is securely supported.
2.
Remove the rear wheel and tire (A) from the rear hub.
Tightening torque :
107.9 - 127.5 N.m (11.0 - 13.0 kgf.m, 79.6 - 94.0 lb-ft)
   
•
Be careful not to damage the hub bolts when removing the rear wheel and tire (A).

3.
Disconnect the rear wheel speed sensor connector (A).

4.
Loosen the screw and then remove the rear drum brake (A).
Tightening torque :
4.9 - 5.9 N.m (0.5 - 0.6 kgf.m, 3.6 - 4.3 lb-ft)

5.
Loosen the hub mounting bolts and then remove the hub (A) from the torsion beam.
Tightening torque :
49.0 - 58.8 N.m (5.0 - 6.0 kgf.m, 36.2 - 43.4 lb-ft)

Inspection
1.
Check the hub for cracks and the splines for wear.
2.
Check the brake disc for scoring and damage.
3.
Check the rear axle carrier for cracks.
4.
Replace only the sensor cap when the warning light turns on due to a defective sensor cap of the hub bearing.
(Refer to Brake System - "Rear Wheel Speed Sensor")
Installation
1.
To install, reverse the removal procedures.

    Repair procedures RemovalThe type can replace the wheel side joint boot1.Remove the front drive shaft.(Refer to Driveshaft Assembly - "Front Driveshaft")2.

    Other information:

    Hyundai Elantra (CN7) 2021-2026 Service Manual: Front View Camera Unit

    Schematic diagrams Circuit Diagram Repair procedures Removal1.Disconnect the negative (-) battery terminal.2.Remove the cover (A) & (B).3.Disconnect the front view camera unit connector (A).4.Separate the fixed points (A) of coupler.5.

    Hyundai Elantra (CN7) 2021-2026 Service Manual: Rear View Monitor (RVM)

    Description and operation DescriptionRear view camera will activate when the backup light is ON with the ignition switch ON and the shift lever in the R position.This system is a supplemental system that shows behind the vehicle through the AV monitor or the ECM (Reverse Display Room Mirror) mirror while backing-up.

    Categories

     
    Copyright © 2026 www.helantra7.com - 0.0154