Hyundai Elantra: DCT(Dual Clutch Transmission) System / Special service tools
Hyundai Elantra (CN7) 2021-2025 Service Manual / DCT(Dual Clutch Transmission) System / Special service tools
| Special Service Tools |
|
Tool
(Number and Name) |
Illustration
|
Use
|
| 09200-3N000 Engine support fixture (Beam) |
| Removal and installation of the transmission. Use this beam (SST No. : 09200-3N000) with the supporter (SST No. : 09200-2S000). |
| 09200-L1100 Engine support fixture (Rear) |
| Removal and installation of the transaxle. with the beam (SST No. : 09200-38001/3N000). |
| 09200-L1200 Engine support fixture (Front) |
| Removal and installation of the transaxle. Use this beam (SST No. : 3N000) with the supporter (SST No. : 09200-2S000). |
| 09200-4X000 Engine support fixture (Adapter) |
| Removal and installation of the transaxle. with the beam (SST No. : 09200-38001/3N000). |
| Oil seal installer 09453-3L240 |
| Used for installing differential oil seal Used with the handle (09231-H1100) |
| Handle 09231-H1100 |
| Used for installing differential oil seal Used with the installer (09453-3L240) |
| Inhibitor switch guide pin 09480-A3800 |
| Used for fixing "N" range when installing inhibitor switch |
| Dual clutch remover 09430-C1180 |
| Used for removing dual clutch assembly |
| Dual clutch installer 09430-2A240 |
| Used for installing dual clutch assembly |
| Clutch actuator remover & installer 0K430-Q5100 |
| Removal and installation of the clutch actuator assembly. |
| Clutch actuator adjuster 0K430-Q5300 |
| Used for adjusting clutch actuator |
Specifications
SpecificationsDual clutch transmission
Item
Specification
Transmission modelD7UF1-2 (7DCT)Engine modelGamma II 1...
Troubleshooting
Troubleshooting
Trouble symptom
Probable cause
Remedy
Displayed the warning lamp "E"(Driving is only possible with 1/ R gear)Not performed DCT learningPerform the DCT manual learning procedure...
Other information:
Hyundai Elantra (CN7) 2021-2025 Service Manual: Repair procedures
Inspection • Wrap the protective tape on the tool to disassemble with the screwdriver or remover. • Use caution in keeping and handling during disassembling/assembling because it is easily contaminated with lubricant and oil...
Hyundai Elantra (CN7) 2021-2025 Service Manual: Water Inlet Fitting
Repair procedures RemovalWater Inlet Fitting1.Remove the engine room under cover.(Refer to Engine and Transaxle Assembly - "Engine Room Under Cover")2.Drain the coolant. (Refer to Cooling System - "Coolant")3.Disconnect the radiator lower hose (A)...
Categories
- Manuals Home
- 7th Gen Hyundai Elantra Owners Manual
- 7nd Gen Hyundai Elantra Service Manual
- Function settings
- Forward Collision–Avoidance Assist (FCA) (sensor fusion)
- Dimensions, Engine specification, Bulb Wattage
- Instrument Panel Overview
- System disabled
Rear center seat belt
When using the rear center seat belt, the buckle with the “CENTER” mark must be used.
WARNING
Make sure that the seatback is locked in place when using the rear center seat belt.
If not, the seatback may move when there is a sudden stop or collision, which could result in serious injury.
Copyright © 2025 www.helantra7.com