Hyundai Elantra: Manual Transaxle System / Specifications
Hyundai Elantra (CN7) 2021-2025 Service Manual / Manual Transaxle System / Specifications
| Specifications |
|
Manual transaxle type
|
FF 6th Manual Transaxle (M6CF3-1)
| |
| Engine type | Gasoline 1.6 T-GDI | |
| Gear ratio | 1st | 3.308 |
| 2nd | 1.962 | |
| 3rd | 1.294 | |
| 4th | 0.976 | |
| 5th | 0.778 | |
| 6th | 0.633 | |
| Reverse | 3.583 | |
| Final gear ratio | 4.467 | |
| Tightening Torques |
|
Items
|
N.m
|
kgf.m
|
lb-ft
|
| Oil drain plug | 58.9 - 78.5 | 6.0 - 8.0 | 43.4 - 57.8 |
| Oil filler plug | 58.9 - 78.5 | 6.0 - 8.0 | 43.4 - 57.8 |
| Shift lever assembly mounting bolt | 8.8 - 13.7 | 0.9 - 1.4 | 6.5 - 10.1 |
| Roll rod bracket mounting bolt | 107.9 - 127.5 | 11.0 - 13.0 | 79.6 - 94.1 |
| 49.0 - 63.7 | 5.0 - 6.5 | 36.2 - 47.0 | |
| Roll rod support bracket bolt | 49.0 - 68.6 | 5.0 - 7.0 | 36.2 - 50.6 |
| Control cable retainer mounting nut | 11.8 - 14.7 | 1.2 - 1.5 | 8.7 - 10.8 |
| Back up lamp switch | 39.2 - 58.8 | 4.0 - 6.0 | 28.9 - 43.4 |
| Control shaft assembly mounting bolt | 19.6 - 26.5 | 2.0 - 2.7 | 14.5 - 19.5 |
| Control cable bracket mounting bolt | 14.7 - 21.6 | 1.5 - 2.2 | 10.8 - 15.9 |
| Transaxle bracket mounting bolt | 58.9 - 78.5 | 6.0 - 8.0 | 43.4 - 57.8 |
| Transaxle bracket support mounting bolt | 88.3 - 107.9 | 9.0 - 11.0 | 65.1 - 79.6 |
| Starter mounting bolt | 49.0 - 63.7 | 5.0 - 6.5 | 36.2 - 47.0 |
| Transaxle upper mounting bolt (TM=>ENG) | 42.2 - 53.9 | 4.3 - 5.5 | 31.1 - 39.8 |
| Transaxle lower mounting bolt (ENG=>TM) | 42.2 - 48.1 | 4.3 - 4.9 | 31.1 - 35.4 |
| 42.2 - 53.9 | 4.3 - 5.5 | 31.1 - 39.8 |
| Lubricant |
|
Item
|
Recommended
|
Capacity
| ||||||
| Manual transaxle oil | API GL-4, SAE 70W, TGO-9 (MS517-14) • Recommended oil
| 1.5 - 1.6 L (0.39 - 0.42 U.S.gal., 1.59 - 1.69 U.S.qt., 1.32 - 1.40 lmp qt.) |
| Sealant |
|
Items
|
Specified sealant
|
Capacity
|
| Control shaft assembly | LOCTITE 5060 or equivalent | As required |
Troubleshooting
Troubleshooting
Symptom
Suspected Area
Remedy
Abnormal noiseOil level (Low)To adding oil after inspect the parts (Oil seal, Drain plug, filler plug)...
Special service tools
Special Service Tools
Tools
(Number and name)
Illustration
Use
Engine support fixture (Beam)09200-3N000Removal and installation of the transaxle...
Other information:
Hyundai Elantra (CN7) 2021-2025 Service Manual: General safety information and caution
PrecautionsGeneral PrecautionsPlease read the following precautions carefully before performing the airbag system service. Observe the instructions described in this manual, or the airbags could accidentally deploy and cause damage or injuries.• When performing electrical inspections, always turn the ignition switch OFF and disconnect the negative cable from the battery, and ..
Hyundai Elantra (CN7) 2021-2025 Service Manual: Repair procedures
Removal1.Disconnect the negative (-) battery terminal.2.Remove the glove box housing cover.(Refer to Body - "Glove Box Housing Cover")3.Remove the IBU unit (A) after loosening mounting nuts.4.Remove the IBU after disconnecting IBU connectors.Installation1.Connect the integrated body control module connector.2.Install the integrated body control module.3.Install the glove box housing cover.4.Connec..
Categories
- Manuals Home
- 7th Gen Hyundai Elantra Owners Manual
- 7nd Gen Hyundai Elantra Service Manual
- Maintenance
- Engine Compartment
- Engine Mechanical System
- Rear Seats
- Fuel gauge
Manual climate control system
To defog inside windshield
.png)
[A] : Type A, [B] : Type B
1. Select any fan speed except “0” position.
2. Select the desired temperature.
3. Select the .png)
or
.png)
position.
Copyright © 2025 www.helantra7.com